On-Off-Battery Container 14,8V | 20Ah | 296Wh, Model SLIM XPRO-20 with 300W Piezo-Switch for Diving Heating Clothing and Light
Features battery tanks for heated diving – Powerful battery power for the heated base layer series E-Thermal Fusion: 
- The battery containers are developed, manufactured and tested quality Made by Heizteufel in Germany
- Compact POM housing with stainless steel latches and waterproof stainless steel grommets with cable kink protection > 100 metre immersion depth
- Water-resistant stainless steel buttons with RGB ring LED and without LED; optional flat and raised designs for a good glove feel
- Electronic switch control with 1 level for ON - OFF - operation
- Electronic switch control with 1 level for ON - OFF - operation
- Water-resistant stainless steel buttons with RGB ring LED and without LEDfor ON - OFF - operation
- On the output side, 2-pole E/O cords used worldwide are used
- A powerful premium charger with active PFC (high efficiency and long service life) and powerful XT60 cable connector
- Stainless steel cable clamps for the battery tank and Cordura textile straps for the belt, backplates and thighs are offered for fastening
- Certification of the battery technology in accordance with UN38.3 and/or MSDS (Material Safety Data Sheet) by accredited test centres
- Our service is always available on working days and responds to your requests and technical requirements with a high level of expertise
14,8V | 20Ah | 296Wh Li-Ion battery tank SLIM XPRO-20 with on-off piezo switch
The SLIM XPRO-20 delivers maximum battery power for heated diving with a heating power increase of >75% compared to known, brand-registered 12V diver batteries.
The battery tank is made in Germany and guarantees a diving depth of >100 metres. Its performance data meets the high requirements for certified diving. It supplies an extensively worn, heated diving suit with the necessary high heat output. Modern high-performance round cells of 21700 Li-Ion technology are assembled into a power pack of 14.8V with 20Ah.
Piezo button circuit
A stainless steel piezo button in the tank head switches on a maximum current load of 300 watts (~20A). The pressure point on the button must be 3~5N and thus ensures defined switching against unintentional contact.
In accordance with the high output current, submersible cords with contacts for high current loads are used.
Battery tank head
The cable outlet on the battery head is kept watertight at 10 bar with a V4A/316L stainless steel grommet. A spiralised V2A/304 stainless steel anti-kink protection also secures the cable against bending stress. The battery head is locked with latches that allow quick and easy opening and closing. O-rings protect against water ingress; it is recommended that these are checked for damage every few weeks and lubricated with rubber fluid or silicone grease to prevent drying out and ageing. All installed components are of premium quality.
Cables and connections .jpg)
The 2-core connection cables, also known as cords, have a standard cable length of ~60cm from the battery tank to the cord connector. The following cables for suit feed-through, which are a Heizteufel brand product as so-called "E-Valve", have a length from the cord plug to the feed-through valve of ~20cm. Other cable lengths are available on request.
Heizteufel's deep-sea-tested plug connections can be disconnected and connected under water if a second battery tank is to be connected during the dive - the power supply must be switched off beforehand. Some of the plugs are equipped with a screwable safety catch to prevent accidental disconnection. The Heizteufel 2-pin cord connections are compatible with Thor, WET or original E/O cords.
Heizteufel's deep-sea-tested plug connections can be disconnected and connected under water if a second battery tank is to be connected during the dive - the power supply must be switched off beforehand. Some of the plugs are equipped with a screwable safety catch to prevent accidental disconnection. The Heizteufel 2-pin cord connections are compatible with Thor, WET or original E/O cords.
On request, brand-specific cables and connectors as well as other systems known from technical diving can be ordered as an option and supplied ready-made by us, e.g. Thor-Cords, WAM-Cords, Fischer for BTS systems, WET-Connect, Santi, Yellow Diving, SubConn.
Optional extensions up to a complete heated system for diving
E-VALVE for APEKS and SITECH valve feedthroughs: Standard valves for dry diving suits are usually supplied by APEKS and SITECH. An intermediate ring is placed under the screwed-on air feed-through, which in the simple version only has a cable feed-through with kink protection for the power supply to the heated clothing.In the extended version, the E-VALVE is equipped with 1 or 2 RGB piezos, which are wired to a multi-channel heating control in the Trockie.
An E-VALVE can be screwed onto an existing feed-through in just a few simple steps and is very easy and safe for the diver to operate.
For divers who do not yet have a feed-through in their drysuit, we supply the SITECH vega valve with a cable inlet and cable outlet for self-installation. The suit should be prepared to accept the Vega valve. If you already have a valve bushing, you can send us your valve for a possible extension conversion with your order. You will receive a ready-made bushing immediately or free of charge together with an order for goods.
E-CONTROL DIVE HEATING CONTROL: A 2-circuit heating control is switched via the RGB piezos of the E-VALVE and provides 4 heating levels, which are switched in the sequence 25%, 50%, 75% and 100% of the heating power.The control unit provides an optical signal control and a vibration warning for heating level switching operations as well as a battery capacity warning if the remaining capacity is not reached. The maximum heat output per heating circuit is 150W. The control unit is pluggable with the E-VALVE piezos and with the heating garment. It is integrated in a flat ABS housing that fits perfectly in the breast pocket of the overalls.
E-FUSION HEATED CLOTHING: Heated shirts, pants, overalls, gloves, socks and bonnets are premium items for the technical diver. We pay attention to the best performance, quality and sustainability of our products - Made in Germany.
An E-VALVE can be screwed onto an existing feed-through in just a few simple steps and is very easy and safe for the diver to operate.
For divers who do not yet have a feed-through in their drysuit, we supply the SITECH vega valve with a cable inlet and cable outlet for self-installation. The suit should be prepared to accept the Vega valve. If you already have a valve bushing, you can send us your valve for a possible extension conversion with your order. You will receive a ready-made bushing immediately or free of charge together with an order for goods.
E-CONTROL DIVE HEATING CONTROL: A 2-circuit heating control is switched via the RGB piezos of the E-VALVE and provides 4 heating levels, which are switched in the sequence 25%, 50%, 75% and 100% of the heating power.The control unit provides an optical signal control and a vibration warning for heating level switching operations as well as a battery capacity warning if the remaining capacity is not reached. The maximum heat output per heating circuit is 150W. The control unit is pluggable with the E-VALVE piezos and with the heating garment. It is integrated in a flat ABS housing that fits perfectly in the breast pocket of the overalls.
E-FUSION HEATED CLOTHING: Heated shirts, pants, overalls, gloves, socks and bonnets are premium items for the technical diver. We pay attention to the best performance, quality and sustainability of our products - Made in Germany.
HEIZTEUFEL: If you have any special product requests that you cannot find on our website, please feel free to send us an enquiry. Our textile department for cutting technology, customisation and production can help in many cases. The technical department for electronics, software and cable and water pressure tests supplies the electrical supplements for the completion of the heating systems.
The suit ducts for heated diving require an electrical cable connection that can be designed according to the required current load (A) and switchable heating zones. The electric valves are available in the following variants
- The Vega-Valve from SiTech is a combination valve for air and electrical cabling, which allows a 2-wire and for 2 differently switched heating circuits a 4-wire cable line in the feed-through.
- The Heizteufel E-Valve is an intermediate ring for the electrical cable feed-through of existing or already installed Apeks and SiTech valves. The screw-on intermediate ring can be used to quickly expand dry suits into a heated suit system.
E-Valves and Vega-Valves come with the following cable and plug variants on the power input side:
- 2-pin Heizteufel-Cord, 2x1.5mm2/core + pin
- 2-pin Thor-Cord (compatible with E/O-Cord and WAM-Cord), 2x1.5mm2/core + pin
- 4-pin Heizteufel cord (compatible with MacArtney „SubConn Micro Circular“ and SEACON „WetCon Micro Circular“), 4x1.5mm2/core + pin
and on the output side in the following cable and connector variants:
- Silicone cables with waterproof RCA plug (dia 12mm), 2x1.0mm2/core (8A) or 2x1.5mm2/core (12A)
- Y-splitter with 2x or 3x waterproof RCA plug silicone cables (dia 12mm), 4x/6x1.0mm2/wire (8A)
- 2- or 4-pole screwable waterproof round connectors (dia 13mm), 2x/4x1.0mm2/core (10A/8A)
- Silicone cables 2x1.5mm2/core (12A) with Santi or Yellow-Diving plug (dia 16mm), 2x0.83mm2/pin (10A)
The scope of delivery of the battery tank includes an electronically controlled, 2-stage CC-CV charger with active PFC (very high efficiency >94% and extremely long operating time of >200,000hrs.) and 5,000mA charging current. A bar graph capacity display of the battery charge status in 12.5% capacity increments is available as an option. A digital, adjustable charging system with display is also available as an option for demanding, technical diving sports, which makes sense via multi-programmability and multi-balancer technology for different operating battery packs.
We can optionally supply the 20Ah battery tanks with a stainless steel cable clip, for example, for attachment to a hose strap and with a fastening strap. Other delivery options include a container fastening bag with a Molle system or a transport bag made of tear-resistant codura textile.
We can optionally supply the 20Ah battery tanks with a stainless steel cable clip, for example, for attachment to a hose strap and with a fastening strap. Other delivery options include a container fastening bag with a Molle system or a transport bag made of tear-resistant codura textile.
Heated dry suits and heated wet suits
Dry diving is favoured in our Central European latitudes. In this respect, the above-mentioned technical equipment is very consistent as the most commonly used diving equipment. For heated wet diving, we have a selection of heated clothing that fulfils the technical heating conditions. Please contact us if required.More options
- Battery tank with/without heating control and with/without piezo button
- Battery tank with on/off switch, 14.8V/20Ah and 40Ah as well as 11.1V/25Ah and 50Ah
- Adaptation to the functional requirements for technical diving or for government safety forces
Notes and features on the accumulators and on the production, service and sales services of Heizteufel in Berlin
The outstanding quality of the individually tested battery packs, the high-quality choice of raw materials used and the electronic protective circuits integrated into the battery packs; this includes the following features
- Automatic switch-off
- Balancing technology
- Deep discharge protection
- Short-circuit protection with reverse polarity protection
- Charge & overvoltage protection
- Discharge current control
- Temperature protection
offer the greatest possible safety for demanding applications and thus correspond to professional battery technology and brand quality, which also stands for a very long battery life.
The battery packs and battery tanks are predominantly individually processed by Heizteufel in order to guarantee the highest level of operational safety for the diver. In total, the following activities listed by Heizteufel are carried out with regard to battery technology:
Technical data
Accumulator/battery cell
Material: rechargeable lithium-ion cells
Type: round cell MT21700 (3.7V / 5,000mAh / 18.5Wh)
Dimensions: diameter 21mm, height 70mm (+/- 1mm)
Battery pack/battery pack
Dimensions:
Height without housing ~150mm
Outer diameter ~ 70mm
Voltage: nominal 14.8V (working range 11.0 ~ 16.8V)
Charging voltage: max. 16.8V
Capacity: ~20Ah, 296Wh
Charging/discharging current: max. 15A
Battery weight: ~1.6kg including protective electronics, plug and cable
Safety technology: Integrated electronics protect the battery pack in the event of/against short circuits, deep discharge, overcharging and overheating
Charging process: balancer process
Protection standards: UN38.3 (Registration number: TCT201217B615), Material Safety Data Sheet (MSDS TCT201217M615)
Battery life: 400-500 charge-discharge cycles or 3 years with regular care and maintenance, whichever comes first
Battery tank/battery housing
Housing material: 100% POM, retaining latch made of V4A stainless steel
Components: Cable entry with kink protection, RGB piezo button, Heizteufel cord connector
Cable conductor: 2-wire with 15A current load/core, optional 4-core power cable with 12A current load/core
Cable connector: waterproof up to 30 bar, 2-pole and 4-pole with 15A current load/pole
Diving depth: for the entire system > 100m, pressure 10 bar
Downforce underwater: ~ 1.8kg at 10m
Housing dimensions:
Height ~ 260mm + ~75mm for the screw connection
Outer diameter ~ 92mm + 7mm for retaining bar
Total weight: ~2.6kg including controls, switches and cables
Heating controls for diving heated clothing
Type: PWM control operated via RGB piezo buttons in waterproof stainless steel design (V4A, 316L)
Number and features of the diver heating controls: 2 pieces each with 296W @ 14.8V DC heating output
Switching power per control: max. 300W @ 16.8V DC
Heating levels: 4-level control with 0 - 25% - 50% - 75% - 100% - 0
Switchability: by pressing a button on the piezo button, each heating level is set at 0.25s between buttons
Operating voltage: 6-17V DC
Electronic charger with active PFC (Premium)
Input voltage: 100-240VAC
Charging voltage: 16.8V DC
Charging current: max. 5A
Dimensions: 170x70x45mm (WxDxH)
Efficiency: >95%
The manufacturer declares conformity to CE 93/68
Accumulator/battery cell
Material: rechargeable lithium-ion cells
Type: round cell MT21700 (3.7V / 5,000mAh / 18.5Wh)
Dimensions: diameter 21mm, height 70mm (+/- 1mm)
Battery pack/battery pack
Dimensions:
Height without housing ~150mm
Outer diameter ~ 70mm
Voltage: nominal 14.8V (working range 11.0 ~ 16.8V)
Charging voltage: max. 16.8V
Capacity: ~20Ah, 296Wh
Charging/discharging current: max. 15A
Battery weight: ~1.6kg including protective electronics, plug and cable
Safety technology: Integrated electronics protect the battery pack in the event of/against short circuits, deep discharge, overcharging and overheating
Charging process: balancer process
Protection standards: UN38.3 (Registration number: TCT201217B615), Material Safety Data Sheet (MSDS TCT201217M615)
Battery life: 400-500 charge-discharge cycles or 3 years with regular care and maintenance, whichever comes first
Battery tank/battery housing
Housing material: 100% POM, retaining latch made of V4A stainless steel
Components: Cable entry with kink protection, RGB piezo button, Heizteufel cord connector
Cable conductor: 2-wire with 15A current load/core, optional 4-core power cable with 12A current load/core
Cable connector: waterproof up to 30 bar, 2-pole and 4-pole with 15A current load/pole
Diving depth: for the entire system > 100m, pressure 10 bar
Downforce underwater: ~ 1.8kg at 10m
Housing dimensions:
Height ~ 260mm + ~75mm for the screw connection
Outer diameter ~ 92mm + 7mm for retaining bar
Total weight: ~2.6kg including controls, switches and cables
Heating controls for diving heated clothing
Type: PWM control operated via RGB piezo buttons in waterproof stainless steel design (V4A, 316L)
Number and features of the diver heating controls: 2 pieces each with 296W @ 14.8V DC heating output
Switching power per control: max. 300W @ 16.8V DC
Heating levels: 4-level control with 0 - 25% - 50% - 75% - 100% - 0
Switchability: by pressing a button on the piezo button, each heating level is set at 0.25s between buttons
Operating voltage: 6-17V DC
Electronic charger with active PFC (Premium)
Input voltage: 100-240VAC
Charging voltage: 16.8V DC
Charging current: max. 5A
Dimensions: 170x70x45mm (WxDxH)
Efficiency: >95%
The manufacturer declares conformity to CE 93/68
